LAMP Stands for Linux, Apache, MySQL, and PHP. Most of the websites work with the above combination.Below are the steps to install LAMP on Fedora 27 / Fedora 26 / 25.
To start off, we will install Apache. Open up the terminal and switch to root.
Type following command on the terminal to install Apache server.
dnf install -y httpd
Start the Apache by using the following command.
systemctl start httpd
Enable Apache to start during every boot, type the following on terminal and hit Enter.
systemctl enable httpd
Configure the firewall to allow HTTP request from the external network. Here we will be using static firewall rules, so will disable firewalld and enable iptables and ip6tables.
firewall-cmd --permanent --add-service=http firewall-cmd --reload
To make sure everything installed correctly we will now test Apache to ensure it is working properly.
Open up any web browser and then enter the following URL in the web address:
You will get the web page saying “Fedora Test Page”. Now the Apache is working fine. Apache’s default document root is /var/www/html on Fedora, and the configuration file is /etc/httpd/conf/httpd.conf. Additional configurations are stored in the /etc/httpd/conf.d/ directory.
Next is to install the MySQL on the Linux, follow the Steps. Type the following command and then Press Enter.
dnf install -y mariadb mariadb-server
Start MySQL server.
systemctl start mariadb
To make the MySQL start during every boot, type the following on terminal and hit Enter.
systemctl enable mariadb
Next is to make the MySQL secure by using the mysql_secure_installation command.
This program enables you to improve the security of your MySQL installation in the following ways:
- You can set a password for
- You can remove
rootaccounts that are accessible from outside the local host.
- You can remove anonymous-user accounts.
- You can remove the
testdatabase (which by default can be accessed by all users, even anonymous users), and privileges that permit anyone to access databases with names that start with
# mysql_secure_installation NOTE: RUNNING ALL PARTS OF THIS SCRIPT IS RECOMMENDED FOR ALL MariaDB SERVERS IN PRODUCTION USE! PLEASE READ EACH STEP CAREFULLY! In order to log into MariaDB to secure it, we'll need the current password for the root user. If you've just installed MariaDB, and you haven't set the root password yet, the password will be blank, so you should just press enter here. Enter current password for root (enter for none): <--- Enter Root password OK, successfully used password, moving on... Setting the root password ensures that nobody can log into the MariaDB root user without the proper authorisation. Set root password? [Y/n] y <--- Yes, if you want to setup root password New password: <--- Type password Re-enter new password: <--- Re type root password Password updated successfully! Reloading privilege tables.. ... Success! By default, a MariaDB installation has an anonymous user, allowing anyone to log into MariaDB without having to have a user account created for them. This is intended only for testing, and to make the installation go a bit smoother. You should remove them before moving into a production environment. Remove anonymous users? [Y/n] <--- Yes to remove anonymous users ... Success! Normally, root should only be allowed to connect from 'localhost'. This ensures that someone cannot guess at the root password from the network. Disallow root login remotely? [Y/n] <--- Disable remote root login ... Success! By default, MariaDB comes with a database named 'test' that anyone can access. This is also intended only for testing, and should be removed before moving into a production environment. Remove test database and access to it? [Y/n] <--- Remove test database - Dropping test database... ... Success! - Removing privileges on test database... ... Success! Reloading the privilege tables will ensure that all changes made so far will take effect immediately. Reload privilege tables now? [Y/n] <--- Reload privilleges ... Success! Cleaning up... All done! If you've completed all of the above steps, your MariaDB installation should now be secure. Thanks for using MariaDB!
By default Apache server supports the HTML language only, not PHP for that we need to install PHP. To install PHP, please follow the steps.
Type following line on the terminal and press enter, this command includes support package for the MySQL.
dnf install -y php php-mysqlnd
You need to restart the apache service after the installation of the PHP, to do that type the following on the terminal.
systemctl restart httpd
For testing the PHP, Place one PHP file on to the default directory of the Apache. The document root of the default web site is /var/www/html. We will now create a small PHP file (info.php) in that directory and call it in a browser. The file will display lots of useful details about our PHP installation, such as the installed PHP version.
In the terminal copy/paste the following line:
# vi /var/www/html/info.php
This command will open up a file called info.php.
Copy/Paste this line into the info.php file:
<?php phpinfo(); ?>
Save and close the file. Use Esc + :wq for saving the file.
Now open your web browser and type the following into the web address:
The page will look like below:
Scroll down the browser to modules section to check the support for the MySQL. You will get the screen like below.